2010 BMW 3 Series

2010 BMW 3 Series recalls (3)

• ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN

  This recall involves aftermarket parts sold by Valeo. Valeo is recalling certain engine cooling fans, part numbers 696121, 696273, and 696275, used as service replacement parts for model year 2008-2011 BMW 1-Series, 2006-2011 BMW 3-Series, 2000-2009 BMW 5-Series, 2004-2005 BMW 6-Series, and 2006-2007 BMW 7-Series vehicles. A metal-oxide semiconductor may overheat due to insufficient screwing of the semiconductor on the aluminum heat sink. This primary failure could cause adjacent components on the fan assembly motor circuit board to overheat and short.

  Remedy: Valeo will notify owners and replace the fans free of charge. The safety recall began on August 22, 2012. This recall is being conducted by Valeo, not by BMW. For further information, owners may contact Valeo at 1-888-718-2536.

• ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)

  BMW of North America, LLC (BMW) is recalling certain 2008-2013 1 Series Coupe (128i); 2007-2013 3 Series Coupe (328i, 328xi, 328i xDrive); 2007-2010 X3 SAV (X3 3.0si, X3 xDrive30i); 2008-2013 1 Series Convertible (128i); 2006-2011 3 Series Sedan (325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi); 2006-2012 3 Series Wagon (328i, 328i xDrive); 2007-2013 3 Series Convertible (328i); 2006-2010 5 Series Sedan (525i, 525xi, 528i, 528xi, 530i, 530xi); 2006-2007 5 Series Wagon (530xi); 2007-2010 X5 SAV (X5 3.0si, X5 xDrive30i); 2006-2008 Z4 Coupe (Z4 3.0si); and 2006-2011 Z4 Roadster (Z4 3.0i, Z4 3.0si, Z4 sDrive30i) vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.

  Remedy: This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Dealers will install an electrical wiring harness with fuse protection for the PCV Valve heater in potentially affected vehicles, free of charge. This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Vehicles previously repaired under the prior recalls will need to come back for the new recall remedy. The remedy is currently being developed. Interim owner notification letters informing owners of the safety risk were mailed on April 1, 2022. Owner notification letters were mailed on July 22, 2022. Owners may contact BMW customer service at 1-800-525-7417.

• ENGINE AND ENGINE COOLING:ENGINE

  BMW of North America, LLC (BMW) is recalling certain 2010-2012 1 Series Coupe, 1 Series Convertible, 3 Series Sedan, 3 Series Convertible, 2010-2011 3 Series Sportswagon, 3 Series Coupe, 5 Series Sedan, X3 xDrive 28i, X3 xDrive 30i, X5 xDrive30i, and Z4 sDrive30i vehicles. The aluminum bolts that secure the housing for the variable camshaft timing adjustment (VANOS) unit can loosen over time and possibly break.

  Remedy: Dealers will replace the four VANOS bolts, free of charge. Interim letters notifying owners of the safety risk are expected to be mailed December 18, 2023. Owner notification letters were mailed June 19, 2024. Owners may contact BMW customer service at 1-800-525-7417.

2010 BMW 3 Series safety ratings

Source: NHTSA NCAP ratings.

2010 BMW 3 Series owner complaints (15)

• ELECTRICAL SYSTEM

  The vehicle constantly and increasingly exhibits the symptoms described in RECALL CAMPAIGN 13V-044: REPAIR BATTERY POSITIVE CABLE, dated XXX , i.e., various electrical malfunctions, including flickering of the instrument cluster, and brief loss of engine power. However, VIN [XXX] is NOT included in this campaign. It appears that the next possibility, even though deemed "extremely isolated" by the recall, is that "the engine may shut off while driving, which leads to a loss of power steering assistance." BMW and NHTSA each state that the other is responsible for including VINs in a recall, yet I am the one at risk of crash. Do I need to seek legal action against both BMW and NHTSA to determine who is responsible for adding the VIN to the recall so BMW can eventually reimburse me for the needed repairs? INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• ENGINE

  I am filing a formal complaint against BMW Seattle for violating federal recall remedy mandates under 49 U.S.C. Chapter 301. The vehicle was delivered for mandatory safety recall 23V-707 after an on-road mechanical shear of the covered VANOS bolts. The dealer has created illegal commercial barriers and failed to fully execute the federal remedy. First, the service department issued a written estimate for $4,405.67, claiming the CAS module and locks failed and required replacement to resolve a no-start condition. I challenged the repair on technical grounds and authorized a new battery and valid key only, the dealer admitted in writing that the electrical sync restored seamlessly and the engine started. They attempted to extract thousands for a functioning module before verifying the recall. Second, the VANOS bolts sheared resulting in certain valve-piston contact. The dealer claimed the engine passed a compression check but refused to provide raw ISTA diagnostic logs to verify this safety threshold. Instead, they demanded an additional out-of-pocket fee of $669.60 to re-perform a test they claimed to have completed, creating a commercial barrier to basic remedy verification. Third, the dealer demanded $2,136.69 to replace a compromised valve cover and PCV valve which functioned without issue pre-failure. Valve cover removal is required for vanos repair and requiring consumer expense for mandatory safety repair is legally prohibited. Indeed, Under BMW SIB 11 09 23, collateral damage must be routed through corporate TSARA, not the consumer. Fourth, the steel VANOS bolt heads sheared completely off. The official remedy mandates dropping the oil pan to locate and remove these fragments to prevent total oil pressure loss. Despite my repeated requests for verification of removal, nothing was provided, the car was inoperable, and I was advised that the recall repair was complete and the vehicle was in outdoor fenced lot awaiting arrangements for removal.

• ELECTRICAL SYSTEM

  Odometer Fraud. The contact purchased a 2010 BMW 328I. It was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 107,414. The contact stated that, while driving 25 MPH over a pothole, several systems in the vehicle unexpectedly reset; however, the speedometer had not reset. The contact stated that the vehicle had not been driven a whole lot. The mileage was reset to approximately 120,000 miles. The contact attempted to retrieve a Carfax Report for the vehicle and became aware that the most recent information on the VIN was posted by the seller. The contact called the seller. No other agencies were contacted.

• SERVICE BRAKES, HYDRAULIC,ENGINE AND ENGINE COOLING,AIR BAGS

  The contact owns a 2010 BMW 328I. The contact received notifications of NHTSA Campaign Numbers: 24V513000 (Air Bags), 23V707000 (Engine and Engine Cooling), and 22V119000 (Engine and Engine Cooling); however, the parts to do the recall repairs were unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The contact stated that while accelerating from the vehicle idling, and turning left or right, the transmission hesitated before shifting hard. Occasionally, while attempting to accelerate, the vehicle unintendedly decelerated, hesitated, and failed to accelerate as intended. The vehicle intermittently stalled, and the contact would release the accelerator pedal, depress the brake pedal, and allow the steering wheel failure to self-correct. The failures became more persistent. The ABS, check engine, X-Drive Fluid, ESC, and TPMS warning lights were illuminated. The contact stated that after adding fluid, the failure persisted. The driver's front seat air bag failed to activate intermittently while the driver's seat was occupied. The heating system occasionally failed to operate. The contact became aware of fluid under the vehicle. The dealer was contacted, but the vehicle was not repaired. The vehicle was taken to a certified mechanic to be diagnosed, and the air bag and traction control warning lights were illuminated. The certified mechanic recommended an oil change because the engine oil was dirty. The vehicle was not repaired. The contact radiator was repaired to resolve the failure with the heating system, but the failures persisted. The manufacturer was not informed of the failures. The failure mileage was unknown.

• ENGINE

  The contact owns a 2010 BMW 328I. The contact stated that the vehicle was taken to the dealer for an unknown recall repair, but the vehicle experienced the failure after the repair. The contact stated that while driving at an undisclosed speed, the vehicle lost automotive power, and the check engine warning light was illuminated. The vehicle was taken back to the dealer, where it was initially diagnosed that the oil cap had failed. The dealer later informed the contact that the camshaft solenoid had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 110,000.

• ENGINE AND ENGINE COOLING

  The contact owns a 2010 BMW 328I. The contact stated that when the vehicle was started, the vehicle was idling rough and occasionally, the vehicle lost automotive power. The contact stated that the failure was intermittent but was more frequent. The contact stated that the check engine warning light was illuminated. While the vehicle was idling, the RPM was fluctuating between 800 - 1,000 RPM. The vehicle was taken to an independent mechanic, who diagnosed the vehicle and determined that there was a failure with the VANOS valve timing system. The contact was informed that the VANOS valve timing system needed to be replaced. The contact researched online and related the failure to NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); however, the VIN was not included in the recall. The vehicle was not repaired. The manufacturer was informed of the failure and advised the contact that recalls were VIN-specific and that the VIN was not included in the recall. The failure mileage was approximately 130,000.

• ELECTRICAL SYSTEM,ENGINE,FUEL/PROPULSION SYSTEM

  2010 bmw 328i xdrive: Had in for recall PCV 1/08/2025. This vehicle has had a prior recall for same issue before i owned in 2014. Motorwerks BMW failed to complete recall, as parts and repair bulletin from BMW OF AMERICA has parts list. Motorwerks just CHOSE to put items, subtitled under other services/self pay. When I asked about this they responded that CAR WAS OUT OF WARRANTY ....as build date put it a year out? A RECALL IS A RECALL ITS FOREVER, OR THE LIFE OF CAR. not when they the dealer/shop and BMW right? i have filed and called and complained to numerous places including NCDS, BMW of AMERICA and have gotten no traction or reasonable response. Now I'm having VANOS related issues, serious issues, but no recall listed?, even though the year and style and build date put it in parameters of SAFETY RECALL not just manufacture voluntary recall.

• ELECTRICAL SYSTEM

  The contact owns a 2010 BMW 335I. The vehicle was a custom-modified vehicle and a company mascot. The contact received notification of NHTSA Campaign Number: 17V676000 (Electrical System); however, the vehicle was not repaired. The contact self-identified as an independent mechanic who wanted to be present when recall repair was performed; however, the contact preferred to have the recall disassociated with the VIN and to perform the recall repair himself. The local dealer was contacted and declined the contact to be present during the recall remedy process. The manufacturer was contacted, but the contact was advised that the request was denied. In addition, the contact was not advised on the recall reimbursement process. The contact wished to perform the recall repair himself and be granted reimbursement. The contact had not experienced a failure.

• ENGINE

  Good Morning Folks, I own a 2010 BMW 335i sedan with approximately 110k miles and I will have to be replacing AGAIN, the valve cover gaskets in the car. The first time I had to replace the VCGs was back in 2016 and the vehicle barely had 50k miles on it. Had to replace the VCGs again in 2020. Milage was approximately 92k miles. Fast forward to today and once again, the VCG are leaking. This is an obvious manufacturer defect and I would request that the NHTSA look into to this reoccurring problem with BMW North America. The replacement cost of the VCGs on these vehicles is costly and because it is happening so frequently, BMW should not only be required to cover the cost of replacement but should also be required to remedy the problem permanently. The leakage could lead to possible ignition and a fire within the engine compartment. Thank you for your attention to this matter. [XXX] Grovetown, Ga 2010 BMW 335i owner [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• ENGINE AND ENGINE COOLING

  A few months ago, I tried to get the above-referenced recall item taken care of at BMW of West Houston (Texas). I was told by the dealership service advisor that it would take at least two days to get the work done. The recall notice, of course, says the work should take about four hours. I was also told that in many cases the valve cover gets bent when performing this work and the cost of the replacement valve cover would be my responsibility. I was very disappointed of course. I don't think that I should pay for anything related to getting a safety recall taken care of. Safety recalls are very serious and for that reason I have sent the enclosed letter to BMW of North America I have also sent a letter to BMW of West Houston, 20822 Katy Freeway, Katy, TX 77449 expressing my disappointment. I am hopeful that I can get this recall, and the several other recalls this particularly car is subject to, taken care· of soon and without much drama. I would appreciate any guidance you can provide.

• ENGINE AND ENGINE COOLING

  The contact owns a 2010 BMW 335I. The contact stated while driving 45 MPH, the vehicle went into LIMP Mode, and the check engine warning light illuminated. The vehicle was not taken to a dealer or an independent mechanic. The vehicle was self-diagnosed, and the contact stated that the camshaft timing bolts needed to be replaced. The vehicle was repaired by the contact. The contact related the failure to NHTSA Campaign Number: 23V707000 (ENGINE AND ENGINE COOLING); however, the VIN was not included in the recall. The manufacturer was notified of the failure and informed the contact that the VIN was not included in the recall. The failure mileage was 150,000.

• VEHICLE SPEED CONTROL,ENGINE

  The contact owns a 2010 BMW 328I. The contact stated that while driving at an undisclosed speed, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. The contact stated the vehicle lost motive power, and the contact drifted over to the shoulder of the roadway. The vehicle was restarted and driven to the intended destination. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The manufacturer was made aware of the failure but provided no assistance. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 135,645.

• AIR BAGS

  The contact owned a 2010 BMW 328i. The contact stated that while driving at 25 MPH, she crashed into the driver's side of another vehicle that was making a turn. The air bags deployed, and the contact's face struck the steering wheel. The fire department and police arrived on the scene, but the contact was unaware if any reports had been filed. The firefighter escorted the contact out of the vehicle, while smoke came from the engine. The contact was transported to the hospital by ambulance and treated for a fractured nose and teeth, shrapnel in the left eye, bruising on the right shoulder and knee, and a concussion. The vehicle was towed to a tow yard, where the insurance company deemed it totaled and determined that the contact was at fault for the collision. The contact later received notification of NHTSA Campaign Number: 24V513000 (Air Bags). The manufacturer was made aware of the failure but informed the contact that the original steering wheel had been replaced. The failure mileage was approximately 150,000.

• ENGINE

  The contact owns a 2010 BMW 328I. The contact stated while driving at an undisclosed speed, the vehicle lost motive power. There was no warning light illuminated. The vehicle was towed to the dealer but was not diagnosed or repaired. The manufacturer was made aware of the failure and referred the contact to the NHSTA Hotline for assistance. The approximate failure mileage was 96,000.

• ENGINE

  I have problems consistent with SI B11 07 14- VANOS gear bolt breaking. BMW lied and said that the problem affected only 200,000 cars when in reality it affected a lot more cars. I am losing oil at a slow rate but after than normal oil loss of a healthy engine and have no external leaks, meaning there is an internal leak. I have a metallic rattling noise as well. These problems are consistent with broken VANOS gear bolt(s). I also have a timing issue code popping up with a check engine light that can be caused by this incident. The car is available for inspection upon request. If the problem persists, the engine could experience critical failure causing harm to the components as well as the driver/passengers. I have not been to a dealer yet. I have a scheduled appointment with NEW COUNTRY BMW on Monday to address the airbag issue. A diagnostic for the issue would cost a lot of money that I do not have.